 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| www..com Precision Thick Film Chip Resistors Precision Thick Film Chip Resistors ERJ G : 0201 ERJ R : 0201, 0402, 0603, 0805 ERJ E : 0603, 0805, 1206, 1210, 1812, 2010, 2512 Type: ERJ 1G ERJ 1R, 2R, 3R, 6R ERJ 3E, 6E, 8E, 14, 12, 1T Features Small size and lightweight High reliability Metal glaze thick fi lm resistive element and three layers of electrodes Compatible with placement machines Taping packaging available Suitable for both reflow and flow soldering Low Resistance Tolerance ERJ1G, 2R, 3E, 6E, 8E, 14, 12, 1T Series ....... 1 % ERJ1R, 2R, 3R, 6R Series ............................ 0.5 % Reference Standards IEC 60115-8, JIS C 5201-8 Explanation of Part Numbers ERJ1R, 2R, 3R, 6R Series, 0.5 % type 1 2 3 4 5 6 7 8 9 10 11 12 E R J 3 R B D 1 0 0 2 V Product Code Thick Film Chip Resistors Size, Power Rating Type: inches 1R : 0201 2R : 0402 3R : 0603 6R : 0805 Power R. 0.05 W 0.063 W 0.063 W 0.1 W Code H B K E T.C.R. Marking T.C.R. 50 10-6/C(ppm/C) (1R, 2R) 50 10-6/C(ppm/C) (3R, 6R) 100 10-6/C(ppm/C) (1R, 2R) 100 10-6/C(ppm/C) (3R, 6R) Resistance Tolerance Code Tolerance D 0.5 % Code C X V Packaging Methods Packaging Pressed Carrier Taping 2 mm pitch (1R) Punched Carrier Taping 2 mm pitch (2R) Punched Carrier Taping (3R, 6R) Resistance Value The first three digits are significant figures of resistance and the last one denotes number of zeros following. Example: 1002 10 k Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Feb. 2006 www..com Precision Thick Film Chip Resistors ERJ1G Series, 1 % type 1 2 3 4 5 6 7 8 9 10 11 12 E R J 1 G E F 1 0 0 2 C Product Code Thick Film Chip Resistors Size, Power Rating Type : inches Power R. 0.05 W 1GE : 0201 Resistance Tolerance Code F Tolerance 1 % Resistance Value The first three digits are significant figures of resistance and the last one denotes number of zeros following. Code C Packaging Methods Packaging Pressed Carrier Taping 2 mm pitch, 15000 pcs. ERJ2R, 3E, 6E, 8E, 14, 12, 1T Series, 1 % type 1 2 3 4 5 6 7 8 9 10 11 12 E R J 8 E N F 1 0 0 2 V Product Code Thick Film Chip Resistors Size, Power Rating Type: inches Power R. 2R : 0402 0.063 W 3E : 0603 0.1 W 6E : 0805 0.125 W 8E : 1206 0.25 W 14 : 1210 0.25 W 12 : 1812 0.5 W 12 : 2010 0.5 W 1T : 2512 1W Code K N S Marking Marking No marking (2R, 3E) 4 digit marking (6E, 8E, 14, 12, 1T) 4 digit marking [12(2010 inches)] Resistance Tolerance Code Tolerance 1 % F Code X V U Packaging Methods Packaging Punched Carrier Taping 2 mm pitch (2R) Punched Carrier Taping (3E, 6E, 8E) Embossed Carrier Taping (14, 12, 1T) Resistance Value The first three digits are significant figures of resistance and the 4th one denotes number of zeros following. Construction Dimensions in mm (not to scale) L a W Protective coating t b Alumina substrate Electrode (Inner) Type (inches) ERJ1G, 1R (0201) ERJ2R (0402) ERJ3R (0603) ERJ6R (0805) ERJ3EK (0603) ERJ6EN (0805) ERJ8EN (1206) ERJ14N (1210) ERJ12N (1812) ERJ12S (2010) ERJ1TN (2512) L 0.60 0.03 Dimensions (mm) W 0.30 0.50 0.80 1.25 0.80 1.25 1.60 2.50 3.20 2.50 3.20 0.03 a 0.10 0.20 0.30 0.40 0.30 0.40 0.50 0.50 0.50 0.60 0.65 0.05 b 0.15 0.25 0.30 0.40 0.30 0.40 0.50 0.50 0.50 0.60 0.60 0.05 t 0.23 0.35 0.45 0.60 0.45 0.60 0.60 0.60 0.60 0.60 0.60 0.03 Mass (Weight) [g/1000 pcs.] 0.15 0.8 2 4 2 4 10 16 27 27 45 1.00 0.05 0.05 0.10 0.05 0.05 Electrode (Between) 1.60 2.00 1.60 2.00 3.20 3.20 4.50 5.00 6.40 0.15 +0.15 -0.05 0.10 0.20 0.15 0.10 0.20 0.20 0.20 0.10 0.15 +0.15 -0.05 0.10 0.20 0.15 0.10 Thick film resistive element 0.20 0.20 0.20 0.10 Electrode (Outer) +0.05 -0.20 0.20 +0.05 -0.15 0.20 0.20 0.20 0.10 0.20 0.20 0.10 0.20 0.20 0.20 0.20 0.10 0.20 0.20 0.20 0.20 0.10 0.20 0.20 0.20 0.20 0.10 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Feb. 2006 www..com Precision Thick Film Chip Resistors Ratings <0.5 %> Type (inches) ERJ1RH (0201) Limiting Element Maximum Overload Resistance Power Rating (2) Voltage (Maximum Voltage Tolerance at 70 C (W) (1) RCWV) (V) (%) (V) 0.05 0.05 0.063 0.063 0.063 0.063 0.1 0.1 15 15 50 50 50 50 150 150 30 30 100 100 100 100 200 200 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 Resistance Range () 1 k to 100 k (E24, E96) 100 to 976 (E24, E96) 100 to 100 k (E24, E96) 10 to 97.6 102 k to 1 M (E24, E96) 100 to 100 k (E24, E96) 10 to 97.6 102 k to 1 M (E24, E96) 100 to 100 k (E24, E96) 10 to 97.6 102 k to 1 M (E24, E96) T.C.R. [ 10 -6 /C (ppm/C)] 50 100 50 100 50 100 50 100 Category Temperature Range (Operating Temperature Range) (C) -55 to +125 -55 to +125 -55 to +125 -55 to +125 -55 to +125 -55 to +125 -55 to +125 -55 to +125 ERJ1RK (0201) ERJ2RH (0402) ERJ2RK (0402) ERJ3RB (0603) ERJ3RE (0603) ERJ6RB (0805) ERJ6RE (0805) <1 %> Type (inches) ERJ1G (0201) Limiting Element Maximum Overload Resistance Power Rating (2) Voltage (Maximum Voltage Tolerance at 70 C (W) (1) RCWV) (V) (%) (V) 0.05 0.063 0.1 0.125 0.25 0.25 0.5 0.5 1 15 50 50 150 200 200 200 200 200 30 100 100 200 400 400 400 400 400 1 1 1 1 1 1 1 1 1 Resistance Range () 10 to 1 M (E24, E96) 10 to 1 M (E24, E96) 10 to 1 M (E24, E96) 10 to 2.2 M (E24, E96) 10 to 2.2 M (E24, E96) 10 to 1 M (E24, E96) 10 to 1 M (E24, E96) 10 to 1 M (E24, E96) 10 to 1 M (E24, E96) T.C.R. [ 10 -6 /C (ppm/C)] 200 100 100 100 100 100 100 100 100 Category Temperature Range (Operating Temperature Range) (C) -55 to +125 -55 to +125 -55 to +155 -55 to +155 -55 to +155 -55 to +125 -55 to +125 -55 to +125 -55 to +125 ERJ2RK (0402) ERJ3EK (0603) ERJ6EN (0805) ERJ8EN (1206) ERJ14N (1210) ERJ12N (1812) ERJ12S (2010) ERJ1TN (2512) (1) Rated Continuous Working Voltage (RCWV) shall be determined from RCWV= Power Rating Resistance Values, or Limiting Element Voltage (max. RCWV) listed above, whichever less. (2) Overload (Short-time Overload) Test Voltage (SOTV) shall be determined from SOTV=2.5 Power Rating or max. Overload Voltage listed above whichever less. -55 C 100 Rated Load (%) 80 60 40 20 0 -60 -40 -20 3E, 6E, 8E 1G, 1R, 2R, 3R, 6R 14, 12, 1T 155 C 125 C 0 20 40 60 80 100 120 140 160 180 Ambient Temperature (C) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 70 C Power Derating Curve For resistors operated in ambient temperatures above 70 C, power rating shall be derated in accordance with the figure on the right. Feb. 2006 www..com Precision Thick Film Chip Resistors Packaging Methods (Taping) Standard Quantity Type ERJ1G, ERJ1R ERJ2RH, ERJ2RK ERJ3R , ERJ3EK ERJ6R , ERJ6EN ERJ8EN ERJ14N ERJ12N ERJ12S ERJ1TN Embossed Carrier Taping 4000 pcs./reel 4 mm Punched Carrier Taping 5000 pcs./reel Kind of Taping Pressed Carrier Taping Pitch (P1) 2 mm Quantity 15000 pcs./reel 10000 pcs./reel Carrier Tape Pressed Carrier Punched Carrier Embossed Carrier fD0 E P1 P2 P0 (Unit : mm) F B T T T A P1 (2 mm pitch) fD1 (Only Emboss) W Type ERJ1G, ERJ1R A 0.38 0.67 0.05 B 0.68 1.17 0.05 W F E P1 2.00 0.10 P2 P0 fD 0 T 0.42 0.52 0.05 0.05 fD1 - - - - - 1.0 +0.10 -0 ERJ2RH, ERJ2RK ERJ3R , ERJ3EK ERJ6R , ERJ6EN ERJ8EN ERJ14N ERJ12N ERJ12S ERJ1TN 0.05 0.05 1.10 0.10 1.65 0.15 1.90 0.10 2.50 0.20 8.00 0.20 3.50 0.05 1.75 0.10 2.00 0.05 4.00 0.10 0.70 0.05 0.840.05 2.00 0.15 2.80 3.50 2.80 0.20 0.20 0.20 3.60 0.20 3.50 4.80 0.20 0.20 4.00 0.10 +0.10 1.50-0 8.00 0.30 5.30 0.20 12.00 0.30 5.50 0.20 6.90 0.20 1.00 0.10 1.5 min. 3.60 0.20 Taping Reel Type T (Unit : mm) fA fB fC W T ERJ1G, ERJ1R ERJ2RH, ERJ2RK fC fB ERJ3R , ERJ3EK ERJ6R , ERJ6EN ERJ8EN ERJ14N 180.0 +0 60 min. 13.0 1.0 -3.0 9.0 1.0 11.41.0 fA W ERJ12N ERJ12S ERJ1TN 13.0 1.0 15.42.0 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Feb. 2006 www..com Precision Thick Film Chip Resistors Recommended Land Pattern In case of flow soldering, the land width must be smaller than the Chip Resistor width to control the solder amount properly. Generally, the land width should be 0.7 to 0.8 times (W) of the width of chip resistor. In case of reflow soldering, solder amount can be adjusted, therefore the land width should be set to 1.0 to 1.3 times chip resistor width (W). Dimensions (mm) Type (inches) a b c Chip Resistor ERJ1G, 1R (0201) ERJ2R (0402) ERJ3R, 3EK (0603) ERJ6R, 6EN (0805) ERJ8EN (1206) ERJ14N (1210) ERJ12N (1812) ERJ12S (2010) ERJ1TN (2512) 0.3 to 0.4 0.5 to 0.6 0.7 to 0.9 1 to 1.4 2 to 2.4 2 to 2.4 3.3 to 3.7 3.6 to 4 5 to 5.4 0.8 to 0.9 1.4 to 1.6 2 to 2.2 3.2 to 3.8 4.4 to 5 4.4 to 5 5.7 to 6.5 6.2 to 7 7.6 to 8.6 0.25 to 0.35 0.4 to 0.6 0.8 to 1 0.9 to 1.4 1.2 to 1.8 1.8 to 2.8 2.3 to 3.5 1.8 to 2.8 2.3 to 3.5 c a b Recommended Soldering Conditions Recommendations and precautions are described below. Recommended soldering conditions for reflow * Reflow soldering shall be performed a maximum of two times. * Please contact us for additional information when used in conditions other than those specified. * Please measure the temperature of the terminals and study every kind of solder and printed circuit board for solderability before actual use. Peak Temperature Preheating Heating For soldering (Example : Sn/Pb) Preheating Main heating Peak Temperature 140 C to 160 C Above 200 C 235 5 C Time 60 s to 120 s 30 s to 40 s max. 10 s For lead-free soldering (Example : Sn/Ag/Cu) Temperature Time Preheating 150 C to 180 C 60 s to 120 s Main heating Above 230 C 30 s to 40 s Peak max. 260 C max. 10 s Time Recommended soldering conditions for flow For soldering Temperature Time 140 C to 180 C 60 s to 120 s 245 5 C 20 s to 30 s For lead-free soldering Temperature Time 150 C to 180 C 60 s to 120 s max. 260 C max. 10 s Preheating Soldering Safety Precautions The following are precautions for individual products. Please also refer to the precautions common to Fixed Resistors shown on page ER3 of this catalog. 1. Take measures against mechanical stress during and after mounting of Precision Thick Film Chip Resistors (hereafter called the resistors) so as not to damage their electrodes and protective coatings. 2. If a transient load (heavy load in a short time) like a pulse is expected to be applied, check and evaluate the operations of the resistors when installed in your products before use. Never exceed the rated power. Otherwise, the performance and/or reliability of the resistors may be impaired. 3. Do not use halogen-based or other high-activity flux. Otherwise, the residue may impair the resistors' performance and/or reliability. 4. When soldering with a soldering iron, never touch the resistors' bodies with the tip of the soldering iron. When using a soldering iron with a high temperature tip, finish soldering as quickly as possible (within three seconds at 350 C max.). 5. As the amount of applied solder becomes larger, the mechanical stress applied to the resistors increases, causing problems such as cracks and faulty characteristics. Avoid applying an excessive amount of solder. 6. Do not apply shock to the resistors or pinch them with a hard tool (e.g. pliers and tweezers). Otherwise, the resistors' protective coatings and bodies may be chipped, affecting their performance. 7. Avoid excessive bending of printed circuit boards in order to protect the resistors from abnormal stress. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Feb. 2006 www..com Safety Precautions (Common precautions for Fixed Resistors) * When using our products, no matter what sort of equipment they might be used for, be sure to make a written agreement on the specifi cations with us in advance. The design and specifi cations in this catalog are subject to change without prior notice. * Do not use the products beyond the specifications described in this catalog. * This catalog explains the quality and performance of the products as individual components. Before use, check and evaluate their operations when installed in your products. * Install the following systems for a failsafe design to ensure safety if these products are to be used in equipment where a defect in these products may cause the loss of human life or other significant damage, such as damage to vehicles (au to mo bile, train, vessel), traffi c lights, medical equipment, aerospace equipment, elec tric heating appliances, combustion/gas equipment, rotating equipment, and disaster/crime prevention equipment. Systems equipped with a protection circuit and a protection device Systems equipped with a redundant circuit or other system to prevent an unsafe status in the event of a single fault (1) Precautions for use * These products are designed and manufactured for general and stan dard use in general elec tron ic equipment (e.g. AV equipment, home electric ap plianc es, offi ce equipment, information and com mu ni cation equipment) * These products are not intended for use in the following special conditions. Before using the products, carefully check the effects on their quality and performance, and determine whether or not they can be used. 1. In liquid, such as water, oil, chemicals, or organic solvent 2. In direct sunlight, outdoors, or in dust 3. In salty air or air with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NO2 4. Electric Static Discharge (ESD) Environment These components are sensitive to static electricity and can be damaged under static shock (ESD). Please take measures to avoid any of these environments. Smaller components are more sensitive to ESD environment. 5. Electromagnetic Environment Avoid any environment where strong electromagnetic waves exist. 6. In an environment where these products cause dew condensation 7. Sealing or coating of these products or a printed circuit board on which these products are mounted, with resin or other materials * These products generate Joule heat when energized. Carefully position these products so that their heat will not affect the other components. * Carefully position these products so that their temperatures will not exceed the category temperature range due to the effects of neighboring heat-generating components. Do not mount or place heat-generating components or inflammables, such as vinyl-coated wires, near these products . * Note that non- cleaning solder, halogen-based highly active fl ux, or water-soluble fl ux may deteriorate the performance or reliability of the products. * Carefully select a fl ux cleaning agent for use after soldering. An unsuitable agent may deteriorate the performance or reliability. In particular, when using water or a water-soluble cleaning agent, be careful not to leave water residues. Otherwise, the insulation performance may be deteriorated. (2) Precautions for storage The performance of these products, including the solderability, is guaranteed for a year from the date of arrival at your company, provided that they remain packed as they were when delivered and stored at a temperature of 5 C to 35 C and a relative humidity of 45 % to 85 %. Even within the above guarantee periods, do not store these products in the following conditions. Otherwise, their electrical performance and/or solderability may be deteriorated, and the packaging materials (e.g. taping materials) may be deformed or deteriorated, resulting in mounting failures. 1. In salty air or in air with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NO2 2. In direct sunlight Feb. 2006 - ER3 - |
Price & Availability of ERJ1GEF472C
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |